* Proof FIXED_FIXED_CONSTANT_POOL (#207) * wip(p1002/1024): Proof RCS-CSM_DIGITAL_AUTOPILOT #249 * done(p1024/1024): Proof RCS-CSM_DIGITAL_AUTOPILOT #249
This commit is contained in:
Glenn Dwiyatcita
committed by
James Harris
James Harris
parent
aba87ac00f
commit
5fac70b6a0
@@ -29,8 +29,8 @@
|
||||
|
||||
# Page 1002
|
||||
# T5 INTERRUPT PROGRAM FOR THE RCS-CSM AUTOPILOT
|
||||
# START OF T5 INTERRUPT PROGRAM
|
||||
|
||||
# START OF T5 INTERRUPT PROGRAM
|
||||
|
||||
BANK 20
|
||||
SETLOC DAPS3
|
||||
@@ -40,7 +40,7 @@
|
||||
|
||||
EBANK= KMPAC
|
||||
REDORCS LXCH BANKRUPT # RESTART OF AUTOPILOT COMES HERE
|
||||
CA T5PHASE # ON A T5 RUPT
|
||||
CA T5PHASE # ON A T5 RUPT.
|
||||
EXTEND
|
||||
BZMF +2 # IF T5PHASE +0, -0, OR -, RESET TO -
|
||||
TCF +3 # IF T5PHASE +, LEAVE IT +. DO A FRESHDAP
|
||||
@@ -57,7 +57,7 @@ RCSATT LXCH BANKRUPT # SAVE BB
|
||||
EXTEND # SAVE Q
|
||||
QXCH QRUPT
|
||||
CAF BIT15 # BIT15 CHAN31 = 0 IF IMU POWER IS ON AND
|
||||
EXTEND # S/C CONT SW IS IN CMC (I.E., IF G/C AUTO
|
||||
EXTEND # S/C CONT SW IS IN CMC (I.E. IF G/C AUTO
|
||||
RAND CHAN31 # PILOT IS FULLY ENABLED)
|
||||
EXTEND
|
||||
BZF SETT5 # IF G/C AUTOPILOT IS FULLY ENABLED,
|
||||
@@ -92,17 +92,15 @@ ONESEK DEC 16284 # 1 SEC(TIME5)
|
||||
CHAN5 EQUALS 5
|
||||
CHAN6 EQUALS 6
|
||||
PRIO34A = PRIO34
|
||||
# CHECK PHASE OF T5 PROGRAM
|
||||
|
||||
# CHECK PHASE OF T5 PROGRAM
|
||||
#
|
||||
# BECAUSE OF THE LENGTH OF THE T5 PROGRAM,IT HAS BEEN DIVIDED INTO
|
||||
# BECAUSE OF THE LENGTH OF THE T5 PROGRAM, IT HAS BEEN DIVIDED INTO
|
||||
# THREE PARTS, T5PHASE1, T5PHASE2, AND THE JET SELECTION LOGIC,
|
||||
# TO ALLOW FOR THE EXECUTION OF OTHER
|
||||
# INTERRUPTS. T5PHASE IS ALSO USED IN THE INITIALIZATION OF THE AUTOPILOT
|
||||
# VARIABLES AT TURN ON.
|
||||
#
|
||||
# THE CODING OF T5PHASE IS...
|
||||
#
|
||||
|
||||
# + = INITIALIZE T5 RCS-CSM AUTOPILOT
|
||||
# T5PHASE = +0 = PHASE2 OF THE T5 PROGRAM
|
||||
# - = RESTART DAP
|
||||
@@ -113,7 +111,7 @@ SETT5 CCS T5PHASE
|
||||
TCF T5PHASE2 # BRANCH TO PHASE2 OF PROGRAM
|
||||
TCF REDAP # RESTART AUTOPILOT
|
||||
|
||||
TS T5PHASE # PHASE 1 RESET FOR PHASE 2
|
||||
TS T5PHASE # PHASE 1 RESET FOR PHASE 2
|
||||
CA TIME5
|
||||
TS T5TIME # USED IN COMPENSATING FOR DELAYS IN T5
|
||||
CAF DELTATT2 # RESET FOR T5RUPT IN 20MS FOR PHASE2
|
||||
@@ -123,7 +121,7 @@ SETT5 CCS T5PHASE
|
||||
# IMU STATUS CHECK
|
||||
|
||||
CS IMODES33 # CHECK IMU STATUS
|
||||
MASK BIT6 # BIT6 = 0 IMU OK
|
||||
MASK BIT6 # BIT6 = 0 IMU OK
|
||||
CCS A # BIT6 = 1 NO IMU
|
||||
TCF RATEFILT
|
||||
FREECHK CS RCSFLAGS # BIT14 INDICATES THAT RATES HAVE NOT BEEN
|
||||
@@ -147,16 +145,13 @@ RATEFILT CA RCSFLAGS # SEE IF RATEFILTER HAS BEEN INITIALIZED
|
||||
TCF KMATRIX # IF NOT, SKIP RATE DERIVATION
|
||||
|
||||
# RATE FILTER TIMING = 7.72 MS
|
||||
#
|
||||
|
||||
# RATE FILTER EQUATIONS
|
||||
#
|
||||
#
|
||||
# DRHO = DELRHO - (.1)ADOT + (1 = GAIN1)DRHO
|
||||
# -1
|
||||
#
|
||||
# ADOT = ADOT + GAIN2 DRHO + KMJ DFT
|
||||
# -1
|
||||
# _ * _ _
|
||||
# - * - -
|
||||
# WHERE DELRHO = AMGB (CDU - CDU )
|
||||
# -1
|
||||
|
||||
@@ -170,7 +165,7 @@ DRHOLOOP TS SPNDX
|
||||
INDEX ATTKALMN # PICK UP DESIRED FILTER GAIN
|
||||
MP GAIN1
|
||||
INDEX DPNDX
|
||||
DAS DRHO # (1 -.064) DRHO
|
||||
DAS DRHO # (1 -.064)DRHO
|
||||
EXTEND
|
||||
# Page 1005
|
||||
INDEX DPNDX
|
||||
@@ -187,7 +182,7 @@ DRHOLOOP TS SPNDX
|
||||
CA CDUX # MEASURED BODY RATES--
|
||||
XCH RHO
|
||||
EXTEND
|
||||
MSU RHO # _ * _ _
|
||||
MSU RHO # - * - -
|
||||
COM # DELRHO = AMGB (CDU - CDU )
|
||||
# -1
|
||||
ZL
|
||||
@@ -219,8 +214,8 @@ DRHOLOOP TS SPNDX
|
||||
TS T5TEMP # (CDUZ - RHO2) SCALED 90 DEGS
|
||||
EXTEND
|
||||
MP AMGB5
|
||||
DAS DELTEMPY # DELTEMPY = AMGB4(CDUY-RHO1)
|
||||
# + AMGB5(CDUZ-RHO2)
|
||||
DAS DELTEMPY # DELTEMPY =AMGB4(CDUY-RHO1)
|
||||
# + AMGB5(CDUZ-RHO2)
|
||||
CA AMGB8
|
||||
EXTEND
|
||||
|
||||
@@ -276,20 +271,20 @@ TENTHSEK TS ATTSEC
|
||||
# Page 1007
|
||||
# WHEN AUTOMATIC MANEUVERS ARE BEING PERFORMED, THE FOLLOWING ANGLE ADDITION MUST BE MADE TO PROVIDE A SMOOTH
|
||||
# SEQUENCE OF ANGULAR COMMANDS TO THE AUTOPILOT--
|
||||
#
|
||||
|
||||
# CDUXD = CDUXD + DELCDUX (DOUBLE PRECISION)
|
||||
# CDUYD = CDUYD + DELCDUY (DOUBLE PRECISION)
|
||||
# CDUZD = CDUZD + DELCDUZ (DOUBLE PRECISION)
|
||||
#
|
||||
# THE STEERING PROGRAMS:
|
||||
|
||||
# THE STEERING PROGRAMS-
|
||||
# 1) ATTITUDE MANEUVER ROUTINE
|
||||
# 2) LEM TRACKING
|
||||
#
|
||||
|
||||
# SHOULD GENERATE THE DESIRED ANGLES (CDUXD, CDUYD, CDUZD) AS WELL AS THE INCREMENTAL ANGLES (DELCDUX, DELCDUY,
|
||||
# DELCDUZ) SO THAT THE GIMBAL ANGLE COMMANDS CAN BE INTERPOLATED BETWEEN UPDATES.
|
||||
#
|
||||
# HOLDFLAG CODING:
|
||||
#
|
||||
|
||||
# HOLDFLAG CODING-
|
||||
|
||||
# + = GRAB PRESENT CDU ANGLES AND STORE IN THETADX, THETADY, THETADZ
|
||||
# AND PERFORM ATTITUDE HOLD ABOUT THESE ANGLES
|
||||
# ALSO IGNORE AUTOMATIC STEERING
|
||||
@@ -306,15 +301,16 @@ TENTHSEK TS ATTSEC
|
||||
# +0 = IN ATTITUDE HOLD ABOUT A PREVIOUSLY ESTABLISHED REFERENCE
|
||||
# - = PERFORMING AUTOMATIC MANEUVER
|
||||
# -0 = NOT USED AT PRESENT
|
||||
#
|
||||
# NOTE THAT THIS FLAG MUST BE SET = - BY THE STEERING PROGRAM IF IT IS TO COMMAND THE AUTOPILOT.
|
||||
|
||||
|
||||
# NOTE THAT THIS FLAG MUST BE SET = - BY THE STEERING PROGRAM IF IT IS TO COMMAND THE AUTOPILOT.
|
||||
# SINCE ASTRONAUT ACTION MAY CHANGE THE HOLDFLAG SETTING, IT SHOULD BE MONITORED BY THE STEERING PROGRAM TO
|
||||
# DETERMINE IF THE AUTOMATIC SEQUENCE HAS BEEN INTERRUPTED AND IF SO, TAKE THE APPROPRIATE ACTION.
|
||||
|
||||
CS HOLDFLAG
|
||||
EXTEND
|
||||
BZMF DACNDLS # IF HOLDFLAG +0,-0,+, BYPASS AUTOMATIC
|
||||
# COMMANDS.
|
||||
# COMMANDS
|
||||
DCDUINCR CAF TWO
|
||||
DELOOP TS SPNDX
|
||||
DOUBLE
|
||||
@@ -339,33 +335,33 @@ DELOOP TS SPNDX
|
||||
|
||||
# Page 1009
|
||||
# RCS-CSM AUTOPILOT ATTITUDE ERROR DISPLAY
|
||||
#
|
||||
# THREE TYPES OF ATTITUDE ERRORS MAY BE DISPLAYED ON THE FDAI:
|
||||
#
|
||||
|
||||
# THREE TYPES OF ATTITUDE ERRORS MAY BE DISPLAYED ON THE FDAI-
|
||||
|
||||
# MODE 1) AUTOPILOT FOLLOWING ERRORS SELECTED BY V61E
|
||||
# GENERATED INTERNALLY BY THE AUTOPILOT
|
||||
#
|
||||
|
||||
# MODE 2) TOTAL ATTITUDE ERRORS SELECTED BY V62E
|
||||
# WITH RESPECT TO THE CONTENTS OF N22
|
||||
#
|
||||
|
||||
# MODE 3) TOTAL ASTRONAUT ATTITUDE ERRORS SELECTED BY V63E
|
||||
# WITH RESPECT TO THE CONTENTS OF N17
|
||||
#
|
||||
|
||||
# MODE 1 IS PROVIDED AS A MONITOR OF THE RCS DAP AND ITS ABILITY TO TRACK AUTOMATIC STEERING COMMANDS. IN THIS
|
||||
# MODE THE ATTITUDE ERRORS WILL BE ZEROED WHEN THE CMC MODE SWITCH IS IN FREE.
|
||||
#
|
||||
# MODE THE ATTITUDE ERRORS WILL BE ZEROED WHEN THE CMC MODE SWITCH IS IN FREE
|
||||
|
||||
# MODE 2 IS PROVIDED TO ASSIST THE CREW IN MANUALLY MANEUVERING THE S/C TO THE ATTITUDE (GIMBAL ANGLES) SPECIFIED
|
||||
# IN N22. THE ATTITUDE ERRORS WRT THESE ANGLES AND THE CURRENT CDU ANGLES ARE RESOLVED INTO S/C CONTROL AXES
|
||||
# AS A FLY-TO INDICATOR.
|
||||
#
|
||||
|
||||
# MODE 3 IS PROVIDED TO ASSIST THE CREW IN MANUALLY MANEUVERING THE S/C TO THE ATTITUDE (GIMBAL ANGLES) SPECIFIED
|
||||
# IN N17. THE ATTITUDE ERRORS WRT THESE ANGLES AND THE CURRENT CDU ANGLES ARE RESOLVED INTO S/C CONTROL AXES
|
||||
# AS A FLY-TO INDICATOR.
|
||||
#
|
||||
# V60 IS PROVIDED TO LOAD N17 WITH A SNAPSHOT OF THE CURRENT CDU ANGLES, THUS SYNCHRONIZING THE MODE 3 DISPLAY
|
||||
|
||||
# V60 IS PROVIDED TO LOAD N17 WITH A SNAPSHOT OF THE CURRENT CDU ANGLES, THUS SYNCHRONIZING THE MODE 3 DISPLAY
|
||||
# WITH THE CURRENT S/C ATTITUDE. THIS VERB MAY BE USED AT ANY TIME.
|
||||
#
|
||||
# THESE DISPLAYS WILL BE AVAILABLE IN ANY MODE (AUTO, HOLD, FREE, G+N, OR SCS) ONCE THE RCS DAP HAS BEEN
|
||||
|
||||
# THESE DISPLAYS WILL BE AVAILABLE IN ANY MODE (AUTO, HOLD, FREE, G+N, OR SCS) ONCE THE RCS DAP HAS BEEN
|
||||
# INITIATED VIA V46E. MODE 1, HOWEVER, WILL BE MEANINGFUL ONLY IN G+N AUTO OR HOLD. THE CREW MAY PRESET (VIA
|
||||
# V25N17) AN ATTITUDE REFERENCE (DESIRED GIMBAL ANGLES) INTO N17 AT ANY TIME.
|
||||
|
||||
@@ -380,43 +376,44 @@ KRESUME1 TCF RESUME # END PHASE 1
|
||||
|
||||
# Page 1010
|
||||
# FDAI ATTITUDE ERROR DISPLAY SUBROUTINE
|
||||
#
|
||||
|
||||
# PROGRAM DESCRIPTION: D. KEENE 5/24/67
|
||||
#
|
||||
# THIS SUBROUTINE IS USED TO DISPLAY ATTITUDE ERRORS ON THE FDAI VIA THE DIGITAL TO ANALOG CONVERTERS (DACS)
|
||||
|
||||
# THIS SUBROUTINE IS USED TO DISPLAY ATTITUDE ERRORS ON THE FDAI VIA THE DIGITAL TO ANALOG CONVERTERS (DACS)
|
||||
# IN THE CDUS. CARE IS TAKEN TO METER OUT THE APPROPRIATE NUMBER OF PULSES TO THE IMU ERROR COUNTERS AND PREVENT
|
||||
# OVERFLOW, TO CONTROL THE RELAY SEQUENCING, AND TO AVOID INTERFERENCE WITH THE COARSE ALIGN LOOP WHICH ALSO USES
|
||||
# THE DACS.
|
||||
#
|
||||
|
||||
|
||||
# CALLING SEQUENCE:
|
||||
#
|
||||
# DURING THE INITIALIZATION SECTION OF THE USER'S PROGRAM, BIT3 OF RCSFLAGS SHOULD BE SET TO INITIATE THE
|
||||
|
||||
# DURING THE INITIALIZATION SECTION OF THE USER'S PROGRAM, BIT3 OF RCSFLAGS SHOULD BE SET TO INITIATE THE
|
||||
# TURN-ON SEQUENCE WITHIN THE NEEDLES PROGRAM:
|
||||
#
|
||||
|
||||
# CS RCSFLAGS # IN EBANK6
|
||||
# MASK BIT3
|
||||
# ADS RCSFLAGS
|
||||
#
|
||||
|
||||
# THEREAFTER, THE ATTITUDE ERRORS GENERATED BY THE USER SHOULD BE TRANSFERED TO THE FOLLOWING LOCATIONS IN EBANK6:
|
||||
#
|
||||
|
||||
# AK SCALED 180 DEGREES NOTE: THESE LOCATIONS ARE SUBJECT
|
||||
# AK1 SCALED 180 DEGREES TO CHANGE
|
||||
# AK2 SCALED 180 DEGREES
|
||||
#
|
||||
|
||||
# FULL SCALED DEFLECTION CORRESPONDS TO 16 7/8 DEGREES OF ATTITUDE ERROR
|
||||
# (= 384 BITS IN IMU ERROR COUNTER)
|
||||
#
|
||||
|
||||
# A CALL TO NEEDLER WILL THEN UPDATE THE DISPLAY:
|
||||
#
|
||||
|
||||
# INHINT
|
||||
# TC IBNKCALL # NOTE: EBANK SHOULD BE SET TO E6
|
||||
# CADR NEEDLER
|
||||
# RELINT
|
||||
#
|
||||
# THIS PROCESS SHOULD BE REPEATED EACH TIME THE ERRORS ARE UPDATED. AT LEAST 3 PASSES THRU THE PRORAM ARE
|
||||
|
||||
# THIS PROCESS SHOULD BE REPEATED EACH TIME THE ERRORS ARE UPDATED. AT LEAST 3 PASSES THRU THE PROGRAM ARE
|
||||
# REQUIRED BEFORE ANYTHING IS ACTUALLY DISPLAYED ON THE ERROR METERS.
|
||||
# NOTE: EACH CALL TO NEEDLER MUST BE SEPARATED BY AT LEAST 50MS TO ASSURE PROPER RELAY SEQUENCING.
|
||||
#
|
||||
# NOTE: EACH CALL TO NEEDLER MUST BE SEPARATED BY AT LEAST 50MS TO ASSURE PROPER RELAY SEQUENCING.
|
||||
|
||||
# ERASABLE USED:
|
||||
# AK CDUXCMD
|
||||
# AK1 CDUYCMD
|
||||
@@ -424,21 +421,23 @@ KRESUME1 TCF RESUME # END PHASE 1
|
||||
# EDRIVEX A,L,Q
|
||||
# EDRIVEY T5TEMP
|
||||
# EDRIVEZ SPNDX
|
||||
#
|
||||
# SWITCHES; RCSFLAGS BITS 3,2
|
||||
#
|
||||
# I/O CHANNELS: CHAN12 BIT 4 (COARSE ALIGN - READ ONLY)
|
||||
|
||||
# SWITCHES: RCSFLAGS BITS 3,2
|
||||
|
||||
# I/O CHANNELS: CHAN12 BIT 4 (COARSE ALIGN - READ ONLY)
|
||||
# Page 1011
|
||||
# CHAN12 BIT 6 (IMU ERROR COUNTER ENABLE)
|
||||
# CHAN14 BIT 13,14,15 (DAC ACTIVITY)
|
||||
#
|
||||
# SIGN CONVENTION: AK = THETAC - THETA
|
||||
# CHAN12 BIT 6 (IMU ERROR COUNTER ENABLE)
|
||||
# CHAN14 BIT 13,14,15 (DAC ACTIVITY)
|
||||
|
||||
|
||||
# SIGN CONVENTION< AK = THETAC - THETA
|
||||
# WHERE THETAC = COMMAND ANGLE
|
||||
# THETA = PRESENT ANGLE
|
||||
|
||||
|
||||
NEEDLER CAF BIT4 # CHECK FOR COARSE ALIGN ENABLE
|
||||
EXTEND # IF IN COARSE ALIGN DO NOT USE IMU
|
||||
RAND CHAN12 # ERROR COUNTERS. DON'T USE NEEDLES
|
||||
RAND CHAN12 # ERROR COUNTERS. DONT USE NEEDLES
|
||||
EXTEND
|
||||
BZF NEEDLER1
|
||||
CS RCSFLAGS # SET BIT3 FOR INITIALIZATION PASS
|
||||
@@ -456,7 +455,7 @@ NEEDLER1 CA RCSFLAGS
|
||||
|
||||
CS BIT6 # FIRST PASS BIT3 = 1
|
||||
EXTEND # DISABLE IMU ERROR COUNTER TO ZERO DACS
|
||||
WAND CHAN12 # MUST WAIT AT LEAST 60 MS. BEFORE
|
||||
WAND CHAN12 # MUST WAIT AT LEAST 60 MS BEFORE
|
||||
NEEDLE11 CS ZERO # ENABLING COUNTERS.
|
||||
TS AK # ZERO THE INPUTS ON FIRST PASS
|
||||
TS AK1
|
||||
@@ -533,19 +532,18 @@ DACLIMIT DEC 16000
|
||||
|
||||
# Page 1014
|
||||
# INITIALIZATION PROGRAM FOR RCS-CSM AUTOPILOT
|
||||
#
|
||||
# THE FOLLOWING QUANTITIES WILL BE ZEROED AND SHOULD APPEAR IN CONSECUTIVE LOCATIONS IN MEMORY AFTER WBODY
|
||||
#
|
||||
# WBODY (+1) DFT TAU2
|
||||
# WBODY1 (+1) DFT1 BIAS
|
||||
# WBODY2 (+1) DFT2 BIAS1
|
||||
# ADOT (+1) DRHO (+1) BIAS2
|
||||
# ADOT1 (+1) DRHO1 (+1) ERRORX
|
||||
# ADOT2 (+1) DRHO2 (+1) ERRORY
|
||||
# MERRORX (+1) ATTSEC ERRORZ
|
||||
# MERRORY (+1) TAU
|
||||
# MERRORZ (+1) TAU1
|
||||
|
||||
# THE FOLLOWING QUANTITIES WILL BE ZEROED AND SHOULD APPEAR IN CONSECUTIVE LOCATIONS IN MEMORY AFTER WBODY
|
||||
|
||||
# WBODY (+1) DFT TAU2
|
||||
# WBODY1 (+1) DFT1 BIAS
|
||||
# WBODY2 (+1) DFT2 BIAS1
|
||||
# ADOT (+1) DRHO (+1) BIAS2
|
||||
# ADOT1 (+1) DRHO1 (+1) ERRORX
|
||||
# ADOT2 (+1) DRHO2 (+1) ERRORY
|
||||
# MERRORX (+1) ATTSEC ERRORZ
|
||||
# MERRORY (+1) TAU
|
||||
# MERRORZ (+1) TAU1
|
||||
FRESHDAP CAF ONE # RESET HOLDFLAG TO STOP AUTOMATIC
|
||||
TS HOLDFLAG # STEERING AND PREPARE TO PICK UP AN
|
||||
# ATTITUDE HOLD REFERENCE
|
||||
@@ -582,7 +580,7 @@ ZEROT5 TS SPNDX # ZERO ALL NECESSARY ERASABLE REGISTERS
|
||||
# MS FROM NOW AND EVERY 100MS THEREAFTER.
|
||||
|
||||
CAF ELEVEN
|
||||
TS ATTKALMN # RESET TO PICK UP KALMAN FILTER TAINS
|
||||
TS ATTKALMN # RESET TO PICK UP KALMAN FILTER GAINS
|
||||
# TO INITIALIZE THE S/C ANGULAR RATES
|
||||
# Page 1015
|
||||
CA CDUX
|
||||
@@ -600,7 +598,7 @@ ZEROT5 TS SPNDX # ZERO ALL NECESSARY ERASABLE REGISTERS
|
||||
TCF IMUAOK
|
||||
TS ATTKALMN # CANNOT USE IMU
|
||||
CAF RCSINITB # PROVIDE FREE CONTROL ONLY
|
||||
TCF RCSSWIT # DON'T START UP RATE FILTER
|
||||
TCF RCSSWIT # DONT START UP RATE FILTER
|
||||
# SIGNAL NO RATE FILTER
|
||||
|
||||
IMUAOK CAF PRIO34 # START MATRIX INITIALIZATION
|
||||
@@ -608,10 +606,10 @@ IMUAOK CAF PRIO34 # START MATRIX INITIALIZATION
|
||||
EBANK= KMPAC
|
||||
2CADR AMBGUPDT
|
||||
|
||||
CAF RCSINIT # CLEAR BIT14 --ASSUME WE HAVE A GOOD IMU
|
||||
RCSSWIT TS RCSFLAGS # CLEAR BIT1 --INITIALIZE T6 PROGRAM
|
||||
# SET BIT3 --INITIALIZE NEEDLES
|
||||
# CLEAR BIT4 --RESET FOR FDAIDSP1
|
||||
CAF RCSINIT # CLEAR BIT14 -ASSUME WE HAVE A GOOD IMU
|
||||
RCSSWIT TS RCSFLAGS # CLEAR BIT1 -INITIALIZE T6 PROGRAM
|
||||
# SET BIT3 -INITIALIZE NEEDLES
|
||||
# CLEAR BIT4 -RESET FOR FDAIDSP1
|
||||
CAF T5WAIT60 # NEXT T5RUPT 60 MS FROM NOW TO ALLOW IMU
|
||||
# ERROR COUNTER TO ZERO.
|
||||
# (MINIMUM DELAY = 15 MS)
|
||||
@@ -632,7 +630,7 @@ T6ADDR 2CADR T6START
|
||||
|
||||
ZEROJET CAF ELEVEN # ZERO BLAST2, BLAST1, BLAST, YWORD2,
|
||||
TS SPNDX # YWORD1, PWORD2, PWORD1, RWORD2,
|
||||
CAF ZERO # AND RWORD1
|
||||
CAF ZERO # AND RWORD1.
|
||||
|
||||
# Page 1016
|
||||
INDEX SPNDX
|
||||
@@ -705,7 +703,7 @@ NOHIAUTO TS ATTKALMN
|
||||
# ROLL, BITS 8,7 FOR YAW, BITS 6,5 FOR
|
||||
# PITCH
|
||||
|
||||
CS RCSFLAGS # SET RATE DAMPING FLAGS (BITS 13,12, AND
|
||||
CS RCSFLAGS # SET RATE DAMPING FLAGS (BITS 13,12,AND
|
||||
MASK OCT16000 # 11 OF RCSFLAGS)
|
||||
ADS RCSFLAGS
|
||||
|
||||
@@ -721,7 +719,7 @@ NOCHANGE CS CH31TEMP
|
||||
# MEANS OF STICKCHK, TO 0, 1, OR 2 FOR NO,
|
||||
# +, OR - ROTATION RESPECTIVELY AS
|
||||
# COMMANDED BY THE RHC.
|
||||
#
|
||||
|
||||
# HOWEVER, IT IS WELL TO NOTE THAT AFTER
|
||||
# THE RHC IS RETURNED TO DETENT, THE
|
||||
# PROGRAM BRANCHES TO AHFNOROT AND AVOIDS
|
||||
@@ -792,7 +790,7 @@ NORATE ZL
|
||||
MASK OCT16000
|
||||
EXTEND # IS RATE DAMPING COMPLETED
|
||||
BZF SPNDXCHK # YES, KEEP CURRENT MERRORX GO TO SPNDXCHK
|
||||
TCF ZEROER # NO, GO TO ZEROER
|
||||
TCF ZEROER # NO,GO TO ZEROER
|
||||
|
||||
MERUPDAT INDEX Q # MERRORX=MERRORX+MEASURED CHANGE IN ANGLE
|
||||
CS MANTABLE -1 # -COMMANDED CHANGE IN ANGLE
|
||||
@@ -815,7 +813,7 @@ OCT01400 OCT 01400 # ROLL FORCED FIRING MASK ORDER OF
|
||||
OCT00060 OCT 00060 # PITCH FORCED FIRING MASK DEFINITION
|
||||
OCT00300 OCT 00300 # YAW FORCED FIRING MASK MUST BE
|
||||
# PRESERVED
|
||||
# FOR INDEXING
|
||||
# FOR INDEXING
|
||||
MANROT OCT 77
|
||||
OCT16000 OCT 16000 # RATE DAMPING FLAGS MASK
|
||||
MANTABLE DEC .0071111
|
||||
@@ -833,8 +831,8 @@ FREEFUNC INDEX RMANNDX # ACCELERATION
|
||||
TS TAU
|
||||
INDEX PMANNDX
|
||||
CA FREETAU # FREETAU 0 SEC
|
||||
TS TAU1 # +1 +0.10 SEC
|
||||
INDEX YMANNDX # +2 -0.10 SEC
|
||||
TS TAU1 # +1 +0.10 SEC
|
||||
INDEX YMANNDX # +2 -0.10 SEC
|
||||
CA FREETAU # (+3) 0 SEC
|
||||
TS TAU2
|
||||
TCF T6PROGM
|
||||
@@ -853,7 +851,7 @@ T6PROGM CAF ZERO # FOR MANUAL ROTATIONS
|
||||
# Page 1021
|
||||
DEC .2112 # FILTER GAIN FOR TRANSLATION, LEM ON
|
||||
DEC .8400 # FILTER GAIN FOR TRANSLATION 2(ZETA)WN DT
|
||||
DEC .2112 # FILTER GAIN FOR 4 DEGREE/SEC MANEUVERS
|
||||
DEC .2112 # FILTER GAIN FOR 2 DEGREES/SEC MANEUVERS
|
||||
GAIN1 DEC .0640 # KALMAN FILTER GAINS FOR INITIALIZATION
|
||||
DEC .3180 # OF ATTITUDE RATES
|
||||
DEC .3452
|
||||
@@ -868,7 +866,7 @@ GAIN1 DEC .0640 # KALMAN FILTER GAINS FOR INITIALIZATION
|
||||
|
||||
DEC .0174 # FILTER GAIN FOR TRANSLATION, LEM ON
|
||||
DEC .3600 # FILTER GAIN FOR TRANSLATION (WN)(WN)DT
|
||||
DEC .0174 # FILTER GAIN FOR 4 DEGREE/SEC MANEUVERS
|
||||
DEC .0174 # FILTER GAIN FOR 2 DEGREES/SEC MANEUVERS
|
||||
GAIN2 DEC .0016 # SCALED 10
|
||||
DEC .0454
|
||||
DEC .0545
|
||||
@@ -884,9 +882,9 @@ STICKCHK TS T5TEMP
|
||||
MASK THREE # INDICES FOR MANUAL ROTATION
|
||||
TS PMANNDX
|
||||
CA T5TEMP
|
||||
EXTEND # MAN RATE 0 0 RATE (DP)
|
||||
MP QUARTER # +1 + RATE (DP)
|
||||
TS T5TEMP # +2 - RATE (DP)
|
||||
EXTEND # MAN RATE 0 0 RATE (DP)
|
||||
MP QUARTER # +1 +RATE (DP)
|
||||
TS T5TEMP # +2 -RATE (DP)
|
||||
MASK THREE # (+3) 0 RATE (DP)
|
||||
TS YMANNDX
|
||||
CA T5TEMP
|
||||
@@ -894,6 +892,8 @@ STICKCHK TS T5TEMP
|
||||
MP QUARTER
|
||||
TS RMANNDX
|
||||
TC Q
|
||||
|
||||
|
||||
KALUPDT TS ATTKALMN # INITIALIZATION OF ATTITUDE RATES USING
|
||||
# KALMAN FILTER TAKES 1.1 SEC
|
||||
|
||||
@@ -918,7 +918,7 @@ FDAIDSP2 CS BIT4 # RESET FOR FDAIDSP1
|
||||
EXTEND
|
||||
BZF FDAITOTL
|
||||
EXTEND
|
||||
DCS ERRORX # OFF - DISPLAY AUTOPILOT FOLLOWING ERROR
|
||||
DCS ERRORX # OFF -DISPLAY AUTOPILOT FOLLOWING ERROR
|
||||
DXCH AK
|
||||
CS ERRORZ
|
||||
TS AK2
|
||||
@@ -973,4 +973,3 @@ WRTN17 EXTEND # GET SET TO COMPUTE TOTAL ASTRONAUT
|
||||
TCF GETAKS
|
||||
|
||||
# Page 1024 (empty page)
|
||||
|
||||
|
||||
Reference in New Issue
Block a user